Now available
Buy now

Technical sheet

Applicable safety standards

When used according to the instructions provided, this product meets or exceeds all applicable fall protection standards, namely OSHA 1926 Subpart M, OSHA 1910, ANSI Z359.1.2007, ANSI A10.32-2012 . Applicable standards and regulations depend on the type of work being performed and may include certain provincial regulations.

Product Features

Individual fall arrest device

The fall arrest system can be used to support MAXIMUM 1 individual fall arrest device in fall arrest applications. The structure must support the loads exerted in the directions authorized by the system, of 2 268 kg (5000 lbs) at least. Maximum free fall is 1.8m (6ft) or up to 3.6m (12ft) when used in conjunction with equipment expressly certified for such use. D-ring applicable: dorsal.

Use of equipment for unintended applications may result in serious injury or death. Maximum 1 tie per connection point.

Detention

The fall arrest system can be used in restraint applications. Restraint devices prevent workers from reaching the end of a place where there is a risk of falling. The length of the fully deployed SRL/SRL should always be considered. The structure must support the loads exerted in the directions authorized by the system, of 453kg (1000lb) at least. No free fall is allowed. Restraints can only be used on surfaces with maximum slopes of 12/12 (vertical/horizontal). D-rings applicable: dorsal, thoracic, lateral, scapular.

Restrictions

Free fall height

The clearance below the anchorage connector must be sufficient to arrest a fall before the user reaches the ground or an obstacle. When calculating the free fall height, take into account a MINIMUM factor of safety of 0.9m (3ft), the deceleration distance, the height of the user, the length of the lanyard / self-retracting lifeline , and all other relevant factors.

Pendulum effect

Before any installation or use, take the necessary measures to eliminate or reduce all risks of pendulum effect. A pendulum effect occurs when the anchor is not directly above the location where a fall occurs. Always work maintaining alignment with the anchor points as close as possible. The pendulum effect greatly increases the risk of serious injury or death in the event of a fall.

Compatibility

When making connections, eliminate any possibility of unwinding. A pull-out occurs when interference between a carabiner and the attachment point causes the gate to accidentally open and disengage. All connections must be selected and found to be compatible with the harness by a competent person. All connector fingers must be self-closing, self-locking and support minimum loads of 1632kg (3600lbs).

Product Features

All personal fall protection systems must be selected and deemed compatible with the harnesses by a competent person. ALWAYS follow all instructions for equipment used in combination with the harness. NEVER attach a connector anywhere other than the D-ring. THE connector finger must be self-closing, self-locking, and support minimum loads of 1632kg (3600lbs). Any excess webbing MUST be stored in harness webbing storage locations.

R link is compatible with all anchor points that correspond to the current CSA standard.

Any type of 5/8 inch slider that is CSA 2259.12 standard is compatible. For any other type of slider, it is possible to test it to ensure compliance with standards. Contact us for more information.

Inspection

Before EACH use, inspect the fall arrest system for any defects, including but not limited to signs of corrosion, deformation, punctures, burrs, rough surfaces, sharp edges, cracks, rust marks , excess paint, excessive heat, alterations and missing or illegible labels. IMMEDIATELY remove the fall arrest system if any defects or damage are found, or if it is exposed to fall arrest forces.

Ensure that the affected work area is free of damage including, but not limited to, debris, rot, rust, degradation, cracks and hazardous materials. Make sure the chosen work area will support the application-specific minimum loads listed in this instruction manual. The work area MUST be stable.

At least every 12 months, a competent person other than the user must inspect the fall arrest system. During the inspection, consider all of the applications and hazards facing the fall arrest system.

Safety Information

Working conditions, including but not limited to exposure to flames, electric shock hazards, presence of sharp objects, abrasive materials, weather conditions and uneven surfaces, should be evaluated by a competent person before selecting a fall protection device.

As part of the workplace analysis, one should anticipate where workers will perform their tasks, the routes they will take to reach that location, and any existing or potential fall hazards they may face. be exposed. Fall protection equipment should be selected by a competent person. This choice must take into account all the potentially dangerous working conditions. All fall protection equipment must be purchased new or in equivalent condition.

Fall protection devices must be selected and installed under the supervision of a competent person, and used in a proper manner. Fall protection devices must be designed to comply with all federal, provincial and safety regulations. The forces exerted on the anchors must be calculated by a competent person.

Unless otherwise specified, the maximum allowable free fall distance for lanyards must not exceed 1.8m (6ft). No free fall is permitted for off-board self-retracting lifelines. Class A self-retracting lifelines must arrest falls less than 61cm (24in); Class B self-retracting lifelines must arrest falls less than 137cm (54in).

Selected harnesses and connectors should follow manufacturer's instructions and be chosen in a compatible size and configuration. Carabiners and other connectors must be selected and applied in a compatible manner. Any risk of stalling must be eliminated. All carabiners must be self-locking and self-closing and never be connected to each other.

A rescue procedure in the event of a fall must be provided. The rescue plan should be project specific. The blast plan must allow employees to rescue themselves or provide other rapid rescue methods. Rescue equipment should be stored in an easily accessible and clearly identified location.

Training of authorized persons to ensure the correct assembly, disassembly, inspection, maintenance, storage and use of the equipment must be carried out by a competent person. Training should include the ability to recognize fall hazards, reduce the likelihood of fall hazards and the proper use of personal fall arrest systems.

NEVER use fall protection equipment of any kind to suspend, lift, support or hoist tools or equipment unless certified for such use. Any equipment subject to fall arrest forces should be removed from service immediately.

The age, physical condition and state of health of the worker can have a significant impact on the latter in the event of a fall. A physician should be consulted if in doubt, for any reason, about a user's ability to withstand and absorb fall arrest forces or perform equipment set-up. Pregnant women and minors should not use this equipment.

Physical damage can occur even if fall protection equipment is functioning properly. Prolonged suspension after a fall can result in serious injury or death. Use trauma straps to reduce the effects of suspension trauma.

en_USEnglish